XenonZcar Banner

Z32 Body Repairs and Upgrades

Exterior jobs that make an aging Z32 look and sound tight again. Most need only hand tools and patience. They're based on Robo's write-ups from his 1992 twin turbo, with the hatch lock repair from Rob Rudeau (credited below).

Replacing the exterior moldings

The moldings around the windshield, roof, doors and T-tops are chrome underneath a black coating. With age the coating wears through and the car looks shabby. Stripping and repainting the old pieces rarely turns out well; new moldings are the better fix and give the car a real facelift.

Difficulty
Moderate. Each type of molding mounts differently.
Tools
Nylon trim pry tools, Phillips and flat screwdrivers, 10 mm socket, black RTV silicone, silicone spray
Cost
Roughly $350 for a full OEM set when Robo did his (prices have changed)
Work in warm weather. In a cold garage the plastic clips and rubber seals are stiff and brittle, and they break. Robo started in freezing weather and gave up until summer.

Part numbers

RH is the passenger side and LH the driver side (US cars).

Molding2-seater2+2
Windshield RH72760-30P0072760-30P00
Windshield LH72761-30P0072761-30P00
Roof, short piece RH73852-30P0073852-32P00
Roof, short piece LH73853-30P0073853-32P00
Door RH80820-30P01—
Door LH80821-30P01—
T-top RH91784-30P2091784-32P20
T-top LH91785-30P20 (see note)91785-32P20
Molding clip (roof and top of windshield)73856-30P1073856-30P10
Windshield molding hook clip72796-30P0072796-30P00

Part numbers as listed by Robo. His 2-seater LH T-top number reads 91875-30P20, which looks like a typo for 91785-30P20. Confirm all numbers with a parts catalog before ordering. Buy at least six of the 73856-30P10 clips (10 to 12 for a slick top); old ones are brittle.

The quarter window molding isn't sold on its own by Nissan; it comes only with the glass. Aftermarket kits (KurumaZ made one) include the quarter window and door moldings. Robo found the aftermarket finish a very close match to new OEM, though a show judge might spot a slight difference.

Windshield moldings

  1. Open the hood. Try sliding the molding a few inches toward the T-top; this usually pops it off the top clip, which stays on the body.
  2. Pry the rest up with nylon tools, only at the clip points. You'll feel them. Prying between clips bends the molding. The four white clips sit in a plastic channel on the body (the "molding fastener"), and a black clip at the bottom hooks the windshield edge. Don't crack the glass.
  3. If the plastic molding fastener pulls off the body (common), glue it back to the body, not the glass with two-part epoxy and let it cure fully. Broken clip pieces left in the channel can be slid to one end and fished out.
  4. New moldings come with the clips and the rubber seal fitted. Tuck the rubber bumper stop on the lower end under the front fender first (a little silicone spray helps), then press the molding down until each clip snaps in.

A slightly spongy feel when you press the new molding is normal; it's the soft seal against the glass. If you want to keep and repaint the old moldings, a windshield shop can remove them without damage.

Short roof pieces behind the T-tops

These took Robo longer than the windshield. Each piece has two white clips that slide and lock over studs on the body. Study how they work before you start. Remove the T-tops, tap the old molding to find which way it slides off (rearward on his car), and lift it off.

  • The clips have a front and back, and a ratchet for side-to-side adjustment. Start with them centered. If one ratchets too far, push it through until it comes apart and reassemble it.
  • The usual method is to fit the clips on the body first, then snap the molding over them. If the molding won't snap on, fit the clips into the molding instead and slide the whole piece on.
  • Make sure both clips lock in the same direction.

Slick tops

Hardtops without T-tops have one long molding running up the windshield and along the roof on each side. Robo lists 73852-32P00 (RH) and 73853-32P00 (LH) for these. They use the same clips, but more of them. Clean the groove, space the new clips evenly starting at the hatch end (not every stud gets one), slide the bottom end under the fender, line up the top end with the rear edge of the roof and snap it down. A little silicone sealant at the upper windshield corner can cure a leak there.

Door moldings

These pry off and press on. The door panel doesn't have to come off.

  1. Open the door and pop the molding off the plastic stud at the rear of the door first.
  2. Pry the molding up from the inside of the door, never against the glass.
  3. Slide the front end of the new molding under the mirror mount (loosen the mirror if needed), check the length at the rear, then press it down, working toward the back. Close the door before pressing hard so you don't load the hinges.

Rear quarter window moldings

The easiest of the set. With the door open, lift the bottom edge with a pry tool (only where the tool can't mark visible paint), get your fingers under it and lift the molding off its three rubber clips. Save the small rubber trim piece glued to its rear end. Clean the area, hang the new molding on the tops of the clips, snap the bottom edge in and glue the rubber trim back on with a dab of black RTV.

T-top moldings

Five screws hold each T-top molding to the T-top's outer metal panel, and most of them are hidden. One option is drilling access holes in the inner plastic bracket; Robo preferred taking the T-top apart, which also lets you reseal the inner weatherstrip. Work indoors on a padded bench.

  1. Remove the inner shade if fitted (it makes a handy tray for screws).
  2. Pry off the lock button, open the handle, remove its trim screw and the trim around the handle. Leave the handle open.
  3. Remove the screw at each end of the garnish cover and pry the cover off.
  4. Remove the five 10 mm nuts holding the plastic bracket: two flange nuts through the glass and three others. Don't touch the lock mechanism screws.
  5. Remove the two screws in the metal end brackets the locking rods pass through.
  6. Peel back the large rubber weatherstrip, leaving it on its aluminum bracket at the ends. Remove the two middle screws and back out the two end screws through the holes in the rubber, then lift the aluminum bracket off.
  7. Remove the small screw at each end on the underside. These hold the glass to the bracket and are also the molding's end screws. They're sealed with silicone, which you'll renew.
  8. Slide the glass out. Keep track of the bolts through the glass; their nuts are already off.
  9. Unclip one end of the plastic bracket from the metal panel and lift it away. The adhesive weatherstrip between them can be reused with black RTV.
  10. Remove the last three screws along the underside of the metal panel and the old molding comes off. Clean the channel.
  11. Fit the new molding with the three center screws only.
  12. Reassemble in reverse. Before tightening, make sure the edge of the glass is under the molding's soft rubber lip, not folding it back. Don't overtighten the nuts through the glass. Put silicone on the two small end screws.

Robo's slow drip at the top front corner of the side windows stopped after this job. He credits the tightened screws and resealed weatherstrip more than the new moldings.

Touching up a scraped molding

For a small scrape through the black coating, mask it off and spray several light coats of a flexible low-gloss trim and bumper paint. It isn't perfect, but it's hard to spot, and it's the kind of paint to use if you do decide to strip and refinish old moldings.

Curing hood rattles and squeaks

A Z32 hood that squeaks or rattles over bumps, or even at idle, usually has a worn latch adjustment. Old hood bumpers, a missing prop rod grommet, loose hinges or something under the hood touching it can add to the noise.

Difficulty
Easy
Tools
12 mm socket and extension, rotary tool with a carbide cutter, white lithium grease
Time
A couple of hours, more if the radiator support needs straightening

Check the lower radiator support first

The lower radiator support under the nose looks like a jacking point, but it isn't. The hood latch's bottom bolt is tied to it by a long vertical bracket, so a car jacked there has the latch, and the hood, pushed up. If the hood edges don't sit flush with the fenders, check this first. To straighten it, remove the nose, intake, oil cooler, fan and the vertical latch bracket, then drive the support back down with a large rubber mallet against a wood block. Never jack the car there; use the jacking points shown in the factory manual's general information section.

Lower the latch

The latch has some adjustment, but on a tired car it's often already at the bottom of its slots. The fix is to lengthen the slots slightly.

  1. Remove the intake T and filter as one piece (unplug the MAF sensor, loosen the clamps and remove the filter bracket bolt) to reach the latch.
  2. Remove the latch's three 12 mm bolts. Taking the latch off completely is best: it keeps metal filings out of the intake and lets you clean and grease it. If you leave it hanging on its cable, plug the intake pipes with rags.
  3. Lengthen the bottom edge of the hole in the vertical bracket by a few millimeters, and the top edges of the two holes in the latch itself. There isn't much metal to spare, so take a little at a time and trial-fit. The latch body bottoms on the bracket after only a few millimeters anyway.
  4. Refit the latch as low as it goes and close the hood to check before the nose and intake go back on.
  5. Set the hood 1 to 1.5 mm below the fenders at the latch (factory spec), then adjust the corner bumpers to bring the hood level with the fenders.

Bumpers, grommet and hinges

  • Hood bumpers: originals are usually squashed. New ones should stand about 15 mm free height.
  • Prop rod grommet: the hard plastic grommet around the rod often crumbles away, and the rod rattles without it.
  • Hinges: each hinge has four 12 mm bolts. The top two are easy. For the bottom two, open the hood to its widest position (wiggle the prop rod into the far notch), remove the fender bolts in the door jamb and the four along the top of the fender, and ease the fender out just enough to get a socket on them. Robo found all eight needed at least half a turn. Don't lose the foam pad under the first fender bolt; it helps seal engine noise.
  • Grease: remove the hinge covers (hood at its widest) and grease the hinges and latch with white lithium grease.
  • Look under the hood for shiny rub marks. On Robo's car, and another he checked, the clutch line's upper bleeder screw on the passenger side was hitting the hood. Deleting that bleeder solved it (see clutch hydraulics).
PartNissan part number
Hood bumper stop65822-01M00
Hood prop rod grommet65722-30P10
Hood hinge cover, driver side65451-30P00
Hood hinge cover, passenger side65450-30P00

A well-adjusted hood should latch fully when dropped from 12 to 18 inches, with a solid sound and no slamming needed.

Louder horns

The stock Z32 horns are weak enough that other drivers often don't hear them, which defeats the point. A pair of good-quality aftermarket electric horns is a simple upgrade. Metal-bodied horns with bolted rims hold up to rain and vibration better than cheap plastic ones.

  • Remove the nose panel between the headlights for access. Taking off the whole front fascia makes it easier but isn't needed.
  • Mount the new horns in the stock locations. The stock power wires plug straight onto them.
  • Give each horn its own short ground wire to the chassis rather than one long common ground across the fascia.
  • Scrape the paint off under each ground connection. A bad ground is the cause nine times out of ten when new horns don't work.
  • If the new horns draw more current than the stock ones, use a relay rather than overloading the stock circuit.

Air horns are much louder, loud enough to hurt someone standing near the front of the car. Check your local rules on horn types.

Body groove pinstripe

A groove near the bottom of the body runs all the way around the car and carries a thin accent stripe. Whenever a panel is painted, most often the front fascia, the stripe has to be replaced.

  • The Nissan part for the front fascia stripe (Robo's car) is 99032-30P85, listed as "accent stripe." It's expensive.
  • Pinstripe from a body shop or a stripe supplier matched it almost exactly in Robo's side-by-side comparison, for a fraction of the cost.
  • Remove the old stripe with a nylon scraper and clean the adhesive residue with a solvent that's safe on your paint.

Nose panel

The nose panel is the rectangular piece between the headlights. A rattling nose panel is usually just old grommets.

  • Removal: open the hood and remove the bolts along the panel's rear edge (and those holding the metal bracket underneath, if fitted). Lift the panel up and back. Its front edge sits over four studs on the body.
  • Rattles: fit four new rubber grommets in the front holes, coated with silicone spray so the panel slides on easily.
  • Two types: 1990 panels are thicker with no emblem. From 1991 the panel carries the Nissan emblem and is thinner, with a metal bracket bolted underneath. Robo suspected the bracket stiffens the front for the airbag crash sensors. Since that's unconfirmed, keep the bracket in place if you modify or swap the panel.
  • Gray strip: early cars have a gray strip between the fog lights. From 1995 the whole front fascia is body color, so painting the strip updates the look.

JDM taillights

The taillights from the Japanese-market Z32, sold in Japan after US sales ended in 1996, give the rear a newer look. They bolt in place of the US lights. The matching JDM center panel has a red 300ZX logo.

  • All the work is from inside the hatch. Remove the carpet and trim up to, but not including, the panels over the rear speakers. The center panel only needs loosening.
  • The studs are long and tight to reach. A deep 8 mm socket and an extension are the right tools.
  • As the factory manual says, warm the butyl sealant with a heat gun (from inside the hatch) before pulling the old lights and fitting the new ones. Push on the studs from inside while easing the light out from outside.
  • Scrape off the bulk of the old sealant. The new lights come with thick sealant, so small traces of the old don't matter.

Check that the lights you buy meet your local lighting rules; side markers and reflectors differ between markets.

Blacking out the rear panel logo

The "300ZX" lettering on the rear center panel is molded in raised, clear plastic on the back of the lens and painted from behind, so it can't just be sanded off the front. Robo's method, adapted from the TwinTurbo.net "make the 300ZX glow" FAQ:

  1. Remove the panel. The four studs along the top edge are threaded; turning them counterclockwise helps remove them.
  2. Separate the clear lens from its black backing by warming the assembly in an oven at about 300–350 °F and working it apart a little at a time. Lower heat and more cycles limit curling of the backing's edges. Use oven gloves; the metal studs get hot.
  3. On the back of the lens, scrape the paint off the raised letters with a flat blade. It takes over an hour. Hold the lens up to the light to find every fleck, because any paint left will show. Don't scratch the flat areas around the letters; scratches show through from the front.
  4. Paint the letters black from behind. Ordinary spray paints wouldn't stick to the bare plastic for Robo; a brushed-on acrylic paint made for plastic did, after an alcohol wipe and five or six coats.
  5. Rejoin the lens and backing by warming them in the oven and pressing them together by hand, repeating a few times. Polish any outside scratches with a plastic polish system.

Once sealed, no light reaches the lens from behind, so it looks solid black even if the paint has a few thin spots.

Third brake light lens (hatch)

On cars with the hatch-mounted third brake light, the bulbs can be changed from inside without removing the lens: take off the trim panel under the hatch and unscrew the gray sockets. To remove the lens itself, for cleaning or replacement:

  1. Remove the small trim piece, then the large panel on the underside of the hatch (three screws along the back edge). Slide it forward and catch it. The two side trim strips along the back edge just pull off.
  2. Remove the two 8 mm nuts at the lens corners. They're anchored in plastic, so if they won't turn easily, stop before you crack the lens.
  3. Squeeze the backs of the four clips through the cutouts in the hatch frame (long hose clamp pliers work well) and slide each half of the lens outward from the center.
The lens is fragile when new and brittle when old. Always hold it by the thick center section; it can break under its own weight if lifted by an end. Save the clips, nuts and seals from an old lens before discarding it; they're expensive to buy.

The bulb-out warning circuit expects the stock bulbs. Different bulbs, or LEDs, can make the brake warning light come on whenever you brake (see Battery, Wiring and Stereo).

Rear hatch lock that won't turn

A hatch lock where the key goes in but won't turn is usually stuck tumblers full of road grime. A simple clean-and-oil doesn't fix it; the lock has to come apart far enough to free the first tumbler. This repair is from Rob Rudeau's how-to on TwinTurbo.net, as written up by Robo. If more than one lock on the car is stiff, try a new key first, because worn keys cause this too. The same method has been used to retrieve a broken-off key.

Difficulty
Easy, but fiddly small parts
Tools
10 mm socket and wrench, flat screwdriver, pliers or a padded vise, small screwdrivers and fine needle-nose pliers, degreaser, penetrating oil, lithium grease
Time
1 to 2 hours
  1. Remove the center trim inside the hatch. Peel back the carpet to reach the two 10 mm nuts on the trim's bottom brackets, remove the two plastic thumbscrews at the top and lift the trim out. Don't pry against the bottom brackets; they snap easily (see the trim bracket repair if one has).
  2. Remove the lock. Undo its two 10 mm nuts, twist the white plastic clip off the rod, unplug the connector and pull the lock out. The hatch still opens with the release by the driver's seat.
  3. Remove the end cap. Hold the lock (padded) and carefully pry off the thin chrome cap on the key end. It's soft and is held by dimples.
  4. Remove the keyhole flap. Pry off the flat bracket under the cap. The flap and its spring will fall out; set them aside.
  5. Remove the C-clip on the other end. The bracket with the white clip comes off (it only refits one way).
  6. Slide the tumbler assembly in about a quarter inch by pushing on that end. This frees it up and exposes the first tumbler by the keyhole, the one that usually sticks.
  7. Clean it. Degrease if it's gummy, then soak with penetrating oil. Work each brass tumbler with a tiny screwdriver until it moves freely.
  8. Test with the key. It must turn now; if it doesn't, it won't once reassembled. Keep cleaning until it does, oil the newly exposed parts, then finish with a light coat of lithium grease, working the key in and out a few times.
  9. Reassemble. Fit the bracket and C-clip. At the key end, the spring's arms point away from the keyhole; hold the flap on the spring and slide the bracket over it. Check the bracket isn't bent from removal.
  10. Snap the end cap on and refit the lock, rod clip, connector and trim.

Improvements from Robo's second lock (1995)

  • Unclip the black sensor bracket from the lock while the lock is still in the car, and leave the sensor connected. The lock is easier to handle without it.
  • With the C-clip off, push the whole tumbler assembly out of the housing and soak it in degreaser. This cleans the tumbler slots far better than working them in place. Oil the tumblers lightly afterwards.
  • The two inner parts interlock before they slide back into the housing. Put a light coat of lithium grease on their outside, where they turn in the housing.
  • Bend the keyhole cover's tabs slightly so it snaps in firmly against the spring. To hold the flap while fitting the cover, push a small screwdriver through the slot in the cover.

Related pages: Z32 Interior Repairs, Z32 Body Differences, Cooling and Brake Upgrades.

Sources Used