XenonZcar Banner

Z32 Twin Turbo Bolt-Ons: Intake, Exhaust, Downpipes and Boost

The VG30DETT responds well to simple bolt-on parts, as long as they go on in the right order and the boost stays within what the rest of the car can support. This page follows the usual path: let the engine breathe first (intake and exhaust), then add boost, and measure everything with a proper gauge. Much of it is based on Robo's experience modifying his 1992 twin turbo over many years (credited below).

Boost is where engines break. Detonation from too much boost or too little fuel can destroy pistons suddenly and loudly, or slowly and silently. Use 92–93 octane or better, check boost with an accurate gauge, and leave a safety margin.

Where to start

  1. Intake and exhaust first. A low-restriction air filter and a free-flowing cat-back let the engine breathe and are needed before you turn the boost up at all.
  2. A small boost increase, a pound or two over the stock level of about 9.5 psi, is reasonable with intake and exhaust done.
  3. Beyond that, the ECU needs reprogramming for the extra air (see ECU tuning), and the fuel system and intercoolers become limits. See the boost guidelines below.

Intake: cone filters and the highway stall

The most common intake upgrade replaces the stock airbox with a cone filter in front of each mass air flow (MAF) sensor, mounted behind the plastic splash shields in the front corners. Two plastic pieces matter here and should both be in place: the splash shield, which protects the filter, and the undertray, which guides air in through the front fascia.

A known problem after fitting cone filters: the engine stalls at highway speed when you press the clutch and lift off the throttle. The MAF is getting a disturbed reading because the filter sits too high, in dead air behind the splash shield. The ECU over-fuels and the engine dies.

A widely shared fix is to put tape on part of the filter to change the airflow. Robo found a better one: move the filter down.

  • Mount the filter so the bottom edge of its front cap lines up with the bottom edge of the splash shield, like a circle sitting on a line. Air then flows freely under the shield into the filter.
  • You may need to loosen the clamps on the rubber intake piece so it can rotate down far enough. Then make the hole in the splash shield for the filter's cap bolt at the new height.
  • Don't hang the filter lower than that: it will pick up water and dirt.

With the filter lowered, the stall went away completely and couldn't be made to happen again.

Exhaust

The Z32 TT has a true dual exhaust. From the engine back, each side has:

  1. Exhaust manifold, tucked tightly against the head.
  2. Turbocharger.
  3. Pre-catalyst (US cars), a small catalytic converter bolted to the turbo, with an oxygen sensor.
  4. Mid-pipe with the main catalytic converter.
  5. Cat-back: the pipes, H-pipe, resonators and mufflers behind the main cats.

The cat-back is the first piece to upgrade. A good 2.5-inch, mandrel-bent stainless cat-back is enough for nearly every bolt-on build. Dyno testing by Greg Dupree found a 3-inch cat-back gained only about 6 rwhp even at the 650 hp level, so 3-inch only pays off on very high-power cars.

  • Mandrel bending matters. A crushed (non-mandrel) bend can cut the pipe's flow area dramatically, and flow falls off very quickly as the pipe gets smaller.
  • The H-pipe joins the two halves and balances them.
  • Resonators only affect sound, but without them the exhaust tends to sound raspy.
  • Aftermarket exhausts are louder than stock. The sound usually mellows over the first few months.

Keep working catalytic converters. Removing or gutting the main cats or the pre-cats on a street-driven car breaks US federal emissions tampering rules, even where the local inspection would not catch it. High-flow cats keep the car legal and, according to owners, sound deeper than straight pipes.

Downpipes

On US cars, the pre-catalysts are the most restrictive part of the exhaust: they make tight right-angle bends and carry catalyst brick right behind the turbos. Replacing them with downpipes lets the turbos spool sooner and is one of the biggest seat-of-the-pants improvements. Japanese-market twin turbos never had pre-cats; they used plain downpipes from the factory. See the legality note above before replacing them on a US street car.

Types of downpipe

TypeDesign
Stock pre-catsRight-angle bends and catalyst brick. The most restrictive option.
Single-tube downpipeSmooth bends, no catalyst. Exhaust and wastegate flow share one tube.
Divorced (partial split)The wastegate flow and the turbine exhaust have separate passages for part of the length, cutting turbulence.
Full split (“super split”)Separate passages for the full length of the pipe.
3-inch expansionFull split, widening to 3 inches at the outlet. Needs 3-inch mid-pipes as well (stock is 2.5 inches).

Any good downpipe is a big step over the pre-cats; the gains between the later types are much smaller. On stock turbos, a used set of divorced or full-split pipes gets most of the benefit for much less money.

  • Match the turbo flange. Stock turbos and other Garrett 4-bolt turbine housings need a 4-bolt downpipe. Many larger aftermarket turbos (Garrett GT-series and similar) use 5-bolt flanges.
  • Replace the oxygen sensors at the same time. They're old, and the downpipes are the time to reach them.
  • Plan the labor. The downpipes are buried. Most installers drop the transmission, so the job pairs well with a clutch replacement.
  • Wrap or coat? Opinions differ, and there is no dyno proof either way. Ceramic coating is durable. Wrap can trap moisture and rust the pipe, and some manufacturers advise against it.

Raising boost

How much is safe

Robo's limits for stock turbos, which line up with common experience:

Supporting modsMaximum boost
Stock (factory boost)about 9.5 psi
Intake and cat-back1–2 psi over stock
Intake, exhaust and reprogrammed ECUabout 12–14 psi
All of the above plus larger intercoolers and injectors15–16 psi, no more on stock turbos

Running right at the limit isn't safe even without knock, because fuel quality and air temperature vary. If the car stutters, cuts out, pings or runs badly after a boost change, assume boost is too high and back it off.

Where the wastegate hoses are

Each turbo's wastegate actuator gets its signal through a hose from a nipple on the black intercooler hard pipe that feeds that side's throttle body. To find them, follow the intercooler hose back from each throttle body; the wastegate hose is on the hard pipe underneath it. You may need to remove an intercooler hose to reach them, especially on the passenger side.

Option 1: boost jets

The cheapest method. A boost jet is simply a MIG welding contact tip pushed into each wastegate hose. The small hole delays the pressure reaching the wastegate, so the turbos make more boost before it opens.

  1. Buy several pairs of tips in different sizes. The size is the hole diameter; the length doesn't matter. Start large, at 0.035″ or bigger; a smaller hole means more boost.
  2. Lubricate the hose end, push the tip in smooth end first (it makes removal easier), and put a small clamp over the jet so air can't leak around it.
  3. Fit matching tips to both turbos.
  4. With an accurate boost gauge connected and a passenger reading it, make full-throttle runs in second and third gear.
  5. Change tip sizes until you reach your target.

There's no formula for tip size versus boost; leaks in the boost hoses and clamps change the result. As an example, 0.030″ tips gave Robo 15–16 psi on stock turbos, but only 10–11 psi on larger aftermarket turbos with stiffer wastegate springs, even with smaller tips.

Option 2: manual boost controller

A manual boost controller (MBC) is an adjustable valve in the wastegate line. It's still cheap, needs no wiring, and works where boost jets can't reach the target.

  • T the two wastegate hoses together and run the joined line to the controller's “to wastegate” port.
  • Connect its “boost source” port to one of the intercooler hard pipe nipples.
  • Leave any bleed fitting supplied with the controller in place.
  • Turn the knob clockwise for more boost. Once you're close, small turns make small changes (on Robo's, a quarter turn was about half a psi). Mark the knob so you can track it, and lock it when you're done.

An electronic boost controller costs more but holds boost more precisely, and helps with boost creep and spikes. The engine doesn't care how boost is controlled, only that it's steady and repeatable. With a sensible margin, a simple controller works fine.

A temporary boost gauge

The stock dash gauge isn't accurate enough for setting boost. You don't need a permanent gauge, though; a temporary one works for setup:

  1. Use an inexpensive mechanical boost/vacuum gauge (for example, reading −30 inHg to +25 psi).
  2. Screw a barbed fitting onto the back of the gauge (seal the threads with Teflon tape) so it takes a 6 mm hose. Avoid the stiff plastic tubing kits; they're hard to seal.
  3. Connect a length of 6 mm silicone hose to a manifold pressure nipple on the intake balance tube under the hood. If you borrow a nipple that's in use, plug the disconnected hose temporarily.
  4. Run the hose between the hood seals and in through a slightly open driver's window. The hood closes fine on it.
  5. At idle it should show around 20 inHg of vacuum. Have a passenger read it during full-throttle runs.

It comes off in a couple of minutes when you're done.

Grounding kit

Extra ground cables between the engine, the body and the battery negative terminal are a cheap, harmless mod. Claims about horsepower are debated, but owners commonly report a smoother idle, easier starting and steadier electrics, and better grounds can only help the ECU's sensors and injector signals on a 30-year-old car.

  • The stock negative battery cable grounds in two places: the body next to the battery and the transmission bell housing. Keep both if you replace the cable.
  • Use cable no thinner than 8 gauge (4 gauge is better), with crimped ring terminals sealed in heat shrink.
  • Pick clean, solid metal points across the engine bay. Robo ran a chain of cables from a fuel filter bracket bolt on the driver's side fender, to a plenum bracket bolt that also bolts to the block, to a ground bolt at the rear of the plenum, to the battery negative, and on to a bracket bolt on the passenger side. Others run each cable separately to the battery. Both approaches work.
  • Don't overtighten bolts into the aluminum plenum.

Related pages: Twin Turbo System, Cooling and Brake Upgrades, ECU Tuning.

Sources Used