Z32 Automatic to 5-Speed Manual Swap
Swapping a Z32 from automatic to the 5-speed manual is very doable. You can keep the automatic car's ECU and its big wiring harnesses (the engine, interior and engine room harnesses). The extra automatic transmission plugs on them simply go unused. The automatic ECU runs a 5-speed fine. The parts are mostly bolt-in; the confusing part is the wiring, which is covered step by step below.
The reverse is not practical. Going from 5-speed to automatic means changing those major harnesses.
Parts list
| Part | Notes |
|---|---|
| 5-speed transmission | NA and TT gearboxes share ratios, shafts and mounts, and the TT one has some heavier-duty internals. They differ where the starter mounts, to suit the flywheel size (see below). The speed sensor gear differs between NA and TT to suit the differential ratio, so use the one that matches your car's differential. |
| Flywheel | Larger on the TT. Resurface a used one, or fit a new or lightweight one. |
| Flywheel bolts (8) | Same NA and TT. Longer than the automatic's flex plate bolts. |
| Clutch kit | Disc, pressure plate, release bearing, pilot bushing and alignment tool. Fit a new kit, not used parts. The clutch must match the flywheel (TT with TT, NA with NA) because of the pressure plate bolt pattern. |
| Pilot bushing | Different for the manual. The automatic's bushing in the end of the crank has to come out first. It can be stubborn without a pilot bushing puller and some heat. |
| Pressure plate bolts (9) | Same NA and TT, and not included in OEM clutch kits. Longer bolts are a good idea with a lightweight flywheel, whose threads tend to strip. |
| Engine-to-transmission plate | One piece on the manual. The automatic uses two pieces so you can reach the torque converter bolts. |
| Driveshaft, front half | The rear half is the same as the automatic's. NA and TT 5-speed front halves are the same length and interchangeable (the TT has bigger U-joints). A one-piece aftermarket shaft is an alternative. |
| Clutch pedal | NA and TT pedals differ because of the TT clutch booster. |
| Clutch master cylinder | The TT one is made for the booster. |
| Clutch slave cylinder | Same NA and TT. |
| Metal clutch lines | Same NA and TT, including the section up to the bleeder on the passenger side apron. They run behind the engine from the master cylinder and are very hard to fit with the engine in. |
| Rubber clutch hose | Slave cylinder to metal line. NA and TT lengths differ, but either works on a converted automatic. Use a new one. |
| Shifter, linkage, brace and bushings | Same NA and TT. Use new bushings. |
| Shifter support | The rubber in used ones is usually torn. Buy new. |
| Two rubber inner shift boots | They fit under the leather boot and cut a lot of gearbox noise and heat. |
| Shift boot and lower metal retainer | The console trim around the shifter is the same as the automatic's; the retainer screws on underneath it. |
| Shift knob | |
| Alternator/transmission harness | The one harness that really differs between automatic and manual. It plugs in behind the passenger headlight and runs down the passenger side of the engine to the gearbox. NA and TT are the same. Fitting a manual one is close to plug-in, with a little splicing on one plug. The other option is to adapt the automatic wiring, as described below. |
| TT only: clutch booster | Optional (see below). |
Installation tips
- Pull the engine if you can. The metal clutch lines run behind the engine, and Z1 Motorsports pulls the engine for this swap partly for that reason.
- The TT clutch booster is optional. TTs came with a vacuum clutch booster, plus a matching pedal, master cylinder and two vacuum tanks (one under the master cylinder, one under the driver's fender). On a converted automatic TT, the NA pedal and master cylinder are cheaper, easier and tidier. The pedal is just firmer.
- Fitting the TT pedal and booster means taking the dash out and letting the steering column down. The clutch pedal assembly is held by five bolts, four at the firewall and one at the top. Fit all five.
Wiring
There are three areas to wire:
- The transmission plugs: speed sensor and reverse lights
- The clutch pedal switches: starter interlock and cruise control cancel
- The starter circuit in the driver's side fender well
When you take the automatic out, unplug its harness at the three connectors in the passenger side of the engine bay (near the HICAS solenoid on a TT) and let it come out with the gearbox. Don't cut it.
1. Transmission plugs
Under the car, two connectors are left hanging on the passenger side:
- The brownish connector plugs into the speed sensor on the manual gearbox. It's the only plug on the gearbox that fits.
- The grayish connector went to the automatic's overdrive solenoid. It isn't used. Tie it up out of the way.
In the engine bay, above the passenger side fender well, three connectors are left where the automatic harness plugged in. Two are for the automatic only and aren't used. The third carries the reverse light circuit on two of its wires, pins 4 and 7. Looking into the connector, the pins are numbered:
| 1 | 2 | 3 | 4 |
| 5 (empty) | 6 | 7 | 8 |
Position 5 has no pin, which tells you which way up the connector is. Run pins 4 and 7 to the reverse light switch on the manual gearbox. Two ways to do it:
- Cut the matching connector off the automatic harness you removed, and splice wires from it down to the reverse switch connector.
- Or keep the automatic harness intact (if you're selling the gearbox) and fit new connectors and wire.
The manual gearbox's neutral switch can be left unconnected.
Cover the end of every wire you cut with heat shrink or tape so nothing can short to ground.
2. Clutch pedal switches
A manual Z32 has two switches on the clutch pedal: one that only lets the engine start with the clutch pressed, and one that cancels the cruise control. The automatic car has neither, and no plug for them.
- Starter interlock switch: the switch closest to the firewall, pushed in when the clutch pedal is pressed all the way down. It's wired to the starter circuit (step 3).
- Cruise control cancel switch: wire it into the cruise cancel switch on the brake pedal, the one closest to the passenger side. Splice it in series with that switch, so pressing either pedal breaks the circuit and drops the cruise control. The clutch switch must be the type whose circuit is closed when its plunger is pushed in (pedal at rest). Check it with a meter before you fit it. The post this is based on says the black switch is the right one and the white one works the opposite way.
Crimp-on splice connectors make this easy.
3. Starter circuit (driver's side fender well)
On an automatic, the starter only works in Park or Neutral. That signal is gone with the automatic, so the car won't crank. In the driver's side fender well, find the black/white and black/yellow wires. Joining them lets the starter work.
Don't just join them, though, or the car will start in gear. Instead, run a pair of wires from them into the car and through the clutch pedal's starter interlock switch, so the starter only works with the clutch pressed. Insulated female spade terminals on the connector pins make this a clean job that's easy to undo.
Finishing up
- Bleed the clutch thoroughly. It's easy, but it can take a while to get all the air out of a new system. See Clutch Master / Slave Cylinder Failure.
- Adjust the clutch pedal height and free play. This is often needed after the swap.
- Test before driving: the car must not crank with the clutch out; the reverse lights should come on in reverse; the speedometer should work; and the cruise control should cancel when you press the clutch.
Sources Used
- Z1 Motorsports (300ZX.com), Z32 automatic to 5 speed transmission conversion: the parts list and NA/TT differences. Rewritten and summarized here; prices and product offers are left out.
- Wiring steps: Gold300ZX's automatic to manual swap wiring post on twinturbo.net.
- Greg Dupree's clutch adjustment post on twinturbo.net.