Z32 Timing Belt and Water Pump Replacement
The VG30DE and VG30DETT in the Z32 use one toothed rubber belt to drive all four camshafts. The engine is an interference design: if the belt breaks or jumps teeth, the valves hit the pistons. A belt job costs a weekend; a snapped belt usually costs the heads. On a 30-year-old car with an unknown history, it's the first job to do.
- Factory interval
- 105,000 miles (1994 manual)
- Engine type
- Interference
- Tensioner
- Hydraulic auto-tensioner
- Belt deflection
- 6–7 mm at 49 N (11 lb)
When to replace it
The 1994 maintenance schedule calls for a new timing belt every 105,000 miles (168,000 km). That figure assumes a belt that's been in the car for normal time, though. Rubber ages whether the car is driven or not, so we'd treat it as 105,000 miles or about 7 years, whichever comes first, and replace it straight away if:
- you don't have a receipt for the last belt job,
- the car has sat for years,
- oil or coolant has been leaking onto the belt (the manual lists both as causes of belt failure), or
- the auto-tensioner is leaking oil.
Parts to replace at the same time
Most of the labor is getting to the belt, so replace everything behind the covers while it's open:
- Timing belt. The same part fits the non-turbo and twin turbo.
- Water pump and gasket. The pump sits behind the timing covers, and a leaking pump soaks the belt in coolant.
- Idler pulley and tensioner pulley. A seized bearing will wreck a new belt.
- Hydraulic auto-tensioner. Replace it if it leaks oil from the rod or diaphragm, or if the rod doesn't hold its position (see the check at the end of the procedure).
- Camshaft seals (4) and the front crankshaft seal. Cheap, and an oil leak here kills the belt.
- Thermostat and gasket, since the coolant is drained anyway.
- Drive belts if they're cracked, and fresh coolant.
Engine mounts are worth a look while the front of the engine is open. They're commonly broken on these cars.
Removal
This follows the 1994 factory service manual (EM section). The car stays on the ground with the engine in place.
- Remove the engine under cover.
- Drain the coolant from the radiator drain cock and both cylinder block drain plugs.
- Remove the radiator, the drive belts, and the cooling fan with its fan clutch.
- Remove the crankshaft pulley bolt. To stop the crank turning, the manual has you remove the starter and lock the flywheel ring gear with a suitable tool. Then pull the crank pulley off with a puller.
- Remove the water inlet and outlet, then the front timing belt covers.
- Screw an M6 stopper bolt into the tensioner arm of the auto-tensioner so the tensioner's pusher can't extend.
- Turn the engine to No. 1 cylinder at top dead center on its compression stroke.
- Remove the auto-tensioner and the timing belt.
Installation
- Check that No. 1 cylinder is still at TDC on compression. The mark on the crankshaft sprocket lines up with the mark on the oil pump housing, and each camshaft sprocket mark lines up with its mark on the rear belt cover.
- Remove all the spark plugs so the engine turns over smoothly while you set the tension.
- Fit the belt. The new belt has white lines that line up with the marks on the camshaft and crankshaft sprockets, and an arrow that points to the front of the car.
- Set the auto-tensioner: squeeze it in a vise until there's a 4 mm (0.16 in) gap between the tensioner arm and the pusher, then put the stopper bolt in to hold it there. Don't press the arm with the stopper bolt fitted, or you'll strip the bolt's threads.
- Install the auto-tensioner with its nut and bolts only finger tight.
Setting the tension
- Push the auto-tensioner lightly toward the belt so it can't slip. Don't push hard, or the belt will end up too tight.
- Turn the crankshaft 10° clockwise and tighten the tensioner nut and bolts to 16–21 N·m (12–15 ft-lb).
- Turn the crankshaft 120° counterclockwise. Loosen the tensioner nut and bolts half a turn and let the tensioner body move as far back as it will go.
- Turn the crankshaft clockwise back to No. 1 TDC.
- Push the end of the pusher with about 59 N (13 lb) of force using a push-pull gauge, and tighten the nut and bolts to 16–21 N·m (12–15 ft-lb) while holding it.
- Turn the crankshaft 120° clockwise, then 120° counterclockwise back to No. 1 TDC.
- Measure belt deflection. Make a small steel plate about 8–10 mm wide and 2–3 mm thick, longer than the belt is wide. Lay it across the belt midway between pulleys and push it with 49 N (11 lb). Deflection should be 6–7 mm (0.24–0.28 in), or average 6–7 mm across the spans the manual shows. If it's out, change the pushing force in step 5 and repeat from step 1.
- Recheck that the tensioner nut and bolts are at 16–21 N·m (12–15 ft-lb).
- Remove the stopper bolt from the auto-tensioner.
- Wait 5 minutes, then check how far the rod sticks out (the gap between the tensioner arm and the pusher). It should stay between 3.5 and 5.2 mm (0.138–0.205 in). If it doesn't, the tensioner is bad.
- Check that the belt sits correctly on every sprocket and pulley, with no slipping or misplacement.
- Refit the covers, crank pulley, water inlet and outlet, fan, drive belts and radiator. Refill and bleed the cooling system.
Before you start the engine, turn it two full turns by hand with the crank bolt. If anything stops it, don't force it: the timing is wrong and a valve is touching a piston.
Torque specs
| Fastener | N·m | ft-lb |
|---|---|---|
| Crankshaft pulley bolt | 216–235 | 159–174 |
| Camshaft sprocket bolts (hold the camshaft so it can't turn) | 123–132 | 90–98 |
| Idler pulley bolt | 43–58 | 32–43 |
| Auto-tensioner nut and bolts | 16–21 | 12–15 |
| Front timing belt cover bolts | 3.7–5.0 | 2.7–3.7 |
For coolant capacity see Fluids and Capacities.
Sources Used
- Nissan 1994 300ZX service manual, EM section: timing belt removal, inspection, installation, tensioner setting and torque specs. Read the EM section
- Nissan 1994 300ZX service manual, MA section: periodic maintenance schedule (timing belt interval). Read the MA section
- Parts shared between the non-turbo and twin turbo: Z1 Motorsports, Z32 NA to TT conversion notes.