XenonZcar Banner

Z32 Cooling and Brake Upgrades

More power means more heat, in the radiator and in the brakes. These are proven upgrades for a Z32 that sees hard driving or track days, along with the problems owners have run into fitting them. They're based on Robo's write-ups from his twin turbo (credited below).

Fitting a thicker radiator

The stock radiator core is a little under an inch thick. Racing radiators such as the Z1-Howe are more than twice as thick, so they sit closer to the engine and the stock mounts need some changes:

  1. Swap the top brackets side to side. The two top brackets hold the radiator down and also carry the clips for the hood prop rod. With the thicker radiator, the passenger bracket goes on the driver's side and vice versa. Notch the brackets or the radiator's mounting tabs where needed so they fit; a slight bend in the bracket makes it hold more snugly.
  2. Cut the clip arm off the driver's side bracket if it hits the radiator cap. Keep the white plastic clip.
  3. Move the hood prop rod clip to the fan shroud. Using a bracket as a template, cut a hole in the top of the shroud for the clip (slightly small, since the shroud is plastic), and grind a channel in the shroud's ridges for the rod. Bend the rod until it sits in both clips without tension.
  4. Trim the upper radiator hose to suit the radiator's new position.
  5. Add a proper rear support. The reused stock brackets hold the radiator down but don't stop it sliding back toward the engine; without anything else, only the upper hose is doing that job. Aftermarket brackets are made for this.

While you're there, replace the hood prop rod grommet and the hood bumper stops if they're original. Old ones crumble and the hood rattles.

PartNissan part number
Radiator bracket, passenger side21547-40P00
Radiator bracket, driver side21549-40P00
Radiator rubber mounting pad21506-40P00
Hood prop rod clip (white plastic)65722-01E00
Hood prop rod grommet65722-30P10
Hood bumper stop65822-01M00

Part numbers as listed by Robo for his 1992 twin turbo. Confirm them for your car before ordering.

Aluminum lower radiator hard pipe

The stock lower radiator hose is long, with two sharp bends. Under sustained full throttle it can collapse and cause overheating, which Robo experienced on track. An aluminum hard pipe with short hose elbows at each end cures that. It's a good upgrade, but install it carefully:

  • Check its clearance from the radiator drain cock. On Robo's car the brass drain cock rubbed through the soft aluminum pipe over bumps and caused a coolant leak. Position the pipe so it can't touch, and pad it at any contact point. An unexplained clunk over bumps may be the pipe hitting the radiator.
  • Use new hose for the elbows. Don't reuse cut-off pieces of the old hose: an aged piece split later, with a crack on top that let the system lose pressure without obvious leaking.
  • A small pinhole in the pipe can be repaired with a metal epoxy after drying and cleaning the pipe, but replacing the pipe is the safer fix.

Watch the temperature gauge after any cooling work. A slow climb was Robo's first warning of a leak. Low coolant or a system that won't hold pressure can also make the engine run poorly before it ever overheats. Coolant is poisonous to pets and children; clean up spills.

350Z Track front rotors with the stock calipers

The front rotors from a Nissan 350Z Track model (Brembo, 12.75 inches) fit the Z32 using caliper adapter brackets that move the stock calipers outward. The stock Z32 front rotors are just under 11 inches. Reusing the stock calipers makes this one of the cheapest true big-brake upgrades.

  • Wheels: the larger rotors need 17-inch or larger wheels (at least 385 mm inside diameter). Stock 16-inch wheels won't fit, and nor will a spare tire that only clears the stock brakes.
  • Calipers: works with the 30 mm rotor calipers, aluminum or cast iron. It does not work with the 1990 non-turbo calipers made for 26 mm rotors.
  • Adapters: these have been made in small batches by Z specialists, and availability comes and goes. Torque every bolt to the kit's specs.
  • What it does: a larger rotor gives the caliper more leverage and soaks up more heat. The main benefit is much less fade in repeated hard stops; on a single stop, the tires are usually the limit.
  • Pad wear: the stock caliper's pads are shaped for the smaller rotor, so the bigger rotor leaves a small lip on the outer edge of the pad. This is reported not to cause problems.

Pads, shims and quiet brakes

  • A good street performance pad makes a big difference on its own. Robo found a large improvement switching to a high-performance street pad. Avoid full race pads on the street; they're very hard on rotors.
  • Fit the anti-squeal shims. They're often missing on older cars. New OEM shims are inexpensive.
  • Use brake grease (synthetic, made for brakes) between the shims and the pad backs, as the factory manual specifies. Without it, even new shims may squeal.
  • For a street car, good pads, stainless brake lines and fresh high-temperature brake fluid are usually enough. Bigger rotors pay off on the track or very hilly roads.

Bench bleeding a new brake master cylinder

Bench bleeding fills a new master cylinder and purges its air before it goes in the car, so you don't push extra air into the brake lines. You'll still bleed the brakes afterwards.

  1. Clamp the master cylinder level in a padded vise. Fit short lengths of clear 3/16-inch tubing to its outlet ports with adapters (parts stores often include them with a rebuilt unit), and run the tubes back into the reservoir, below the fluid level.
  2. Fill the reservoir with fresh fluid of the type your car uses.
  3. Push the piston in slowly with a blunt tool such as a socket extension, and let it return. Repeat until no bubbles come out of the tubes.
  4. Remove the tubes, plug the ports, fit the cap and install the master cylinder. Then bleed the brakes.

On ABS cars, the ABS actuator's bleed points are under the trim panel behind the passenger seat. Run a tube from the bleeder into a bottle so fluid can't spill inside the car. Brake fluid strips paint; cover painted surfaces and rinse spills with water at once.

Brake master cylinder brace

Under hard braking the firewall flexes forward, taking the brake master cylinder with it, which makes the pedal feel soft. A master cylinder brace mounts to solid points nearby (on Robo's car, under the fuel filter bracket bolts) and has an adjustable stop that bears on the end of the master cylinder. It noticeably firms up the pedal.

Related pages: Rebuilding the Front 4-Piston Calipers, Wheels and Tires, Twin Turbo Bolt-Ons.

Sources Used