XenonZcar Banner

Z32 Battery, Wiring and Stereo

Electrical jobs and pitfalls on the Z32, from the battery to the speakers. Based on Robo's write-ups from his 1992 twin turbo (credited below).

Battery and cables

The stock battery sits under the edge of the passenger-side windshield cowl, so the small cowl panel has to come off to remove it. The panel is held by four plastic fasteners (two round, two square); back the screws out and pry the clips up gently. They're fragile, so keep spares.

PartNissan part number
Cowl fastener, round66860-01W01
Cowl rivet, square66814-01A00
  • A smaller sealed battery (Robo used an AGM starting battery) can come out with the cowl in place. Pick a starting battery for normal use; a deep-cycle type only makes sense for a big stereo or an alarm left on during long storage.
  • Check hood clearance. With the battery sitting on a spacer tray, Robo's positive terminal touched the underside of the hood. It arced, shut the car down and welded the terminal. Make sure there's clear space above both terminals with the hood shut, using a shorter battery, no tray, or lower-profile terminals. Fit the positive terminal cover.
  • Make good connections. Replace chewed-up or corroded terminal ends with quality clamps, and remove old ring terminals so cables seat directly in the clamp.
  • Don't leave the ground cable stretched tight. Robo's was too short for the new battery, so he added a short 2-gauge extension from the ground bracket behind the battery to the negative terminal. The engine is also grounded at the transmission bell housing.
  • Secure the battery with a proper hold-down. Cut the tie-down rods to suit if needed (the front rod is longer than the rear).

Firewall connectors that are easily swapped

Along the middle of the firewall on the driver's side are the connectors for the knock (detonation) sensor, the driver-side VTC solenoid and the driver-side oxygen sensor. The knock sensor and VTC connectors will plug into each other, and mechanics who don't know these cars sometimes swap them.

  • Nothing gets damaged, but the engine runs poorly, the ECU sets code 34 (knock sensor) and the VTC stops working, costing power.
  • On the harness side, the knock sensor wires are gray and white. The VTC wires are green/black and red/black, and the VTC lead has a white sleeve, which tells it apart from the knock sensor lead.
  • If code 34 appears after any work near the back of the engine, check these first. See ECU trouble codes.

The plastic harness cover there gets brittle with heat. Robo replaced his with split loom.

Brake warning light after an LED third brake light

The Z32 monitors its brake light bulbs. Swapping the third brake light for LEDs, for example with an aftermarket spoiler, changes the current the monitor sees, so the brake warning light in the cluster comes on whenever you press the pedal.

  • Resistors are a poor fix. Robo tried many values. The ones small enough to keep the LEDs bright got hot enough to smoke; the ones that fixed the light dimmed the LEDs to almost nothing. Mixing incandescent and LED lights in one monitored circuit doesn't work well.
  • His solution was to remove that bulb from the cluster. The cluster comes out with a Phillips screwdriver (disconnect the battery first). Remove the screws on the back, release the clips around the edge to separate the clear lens from the housing (leave the wires along the bottom attached), pry out the small four-bulb holder and remove the upper right bulb.
The same light warns of low brake fluid and burned-out brake lights. Before removing that bulb, find out which bulb in the holder you're pulling and what else it covers on your car. With it gone, you must check the brake fluid level and your brake lights regularly yourself. Keeping a working warning light is the safer choice; an LED unit designed for the monitored circuit avoids the problem.

Replacing the Bose stereo in the stock locations

Robo replaced his failing Bose system with an aftermarket head unit, component speakers in front, coaxials in the rear and a compact 4-channel amplifier under the passenger seat, keeping all the stock openings and storage space. His tips:

Doors

  • The front speaker grilles are part of the door panels, so the panels have to come off.
  • The screw under the small round cap on the outside of the door pillar is easy to drop into the body. Curl a piece of cardboard under it as a chute so it falls out instead.
  • With the door panel off, thread the upper seat belt bolt back in by hand so its spacers don't get lost and the belt still works.
  • OEM non-Bose speaker brackets replace the Bose boxes. One corner of each had to be trimmed to clear wiring in the door. Put sound deadening where metal touches metal to stop buzzes.
  • Crossovers that are too thick to fit behind the door panel can be mounted with their lids off, against the door. Keep them close to the speakers.
  • Aim the tweeters at the listener. Robo tried them behind the dash vents and found the sound clearly worse; high frequencies need a clear path.

Rear speakers

  • 1990 rear speaker boxes have 6.5-inch openings; later years have much smaller ones. Even slim aftermarket speakers rub the trim over the boxes.
  • The cleanest fix is to replace the box top with a flat board cut for your speaker. This works on any year's box.
  • Wiring: each Bose speaker had its own amplifier, so four wires run to each rear box. On Robo's '92, the speaker pair was the thinner white/green and brown/white wires; the thicker solid brown and green/white wires fed the Bose amplifier and aren't used. Verify with a wiring diagram for your year.

Head unit, amplifier and grounds

  • The center bezel around the vents and radio removes as described on Interior Repairs. A wiring harness adapter and antenna adapter for the car make the head unit plug-in.
  • To get the head unit's face flush with the bezel, the mounting brackets may need new holes drilled further back.
  • The amplifier power cable can enter the cabin through a grommet behind the passenger-side inner fender (peel the liner back), with an inline fuse near the battery. A long flexible pickup tool snakes wires under the carpet without cutting it.
  • Ground to bare metal. Robo grounded the amp to the shifter plate and heard a big improvement in bass after grinding the paint away under the terminal. There's a good factory ground behind the head unit; scrape it clean too.
  • An amplifier under the seat can be held with short screws into the carpet and pad only. Never drill into the floor pan, where fuel and brake lines may run.

Power antenna mast

To replace a broken mast, remove the round cover plate from inside the hatch first, then the mast nut on top. Padded needle-nose pliers may save the nut; many owners just buy a new one (Nissan 28219-30P10). Check the replacement mast is the right diameter; a cheap one Robo tried was too thin. You can test the motor with the mast fitted by connecting it temporarily and switching the radio on and off.

Washing the engine bay safely

Owners are split on this, but Robo cleaned his very dirty engine bay many times at a self-service car wash with no long-term problems. If you do it:

  • Use a car wash wand or low-pressure washer, never a high-pressure machine that can strip paint or force water into connectors.
  • Use a degreaser that's safe on paint and rubber (not oven cleaner), and don't aim water directly at connectors, the alternator or the coil packs.
  • Pack connectors with dielectric grease beforehand, and spray a water-displacing lubricant on them afterward.
  • Robo kept the engine running while washing, so a misfire told him where not to spray. Many prefer to wash a cool engine that's off; either way, don't spray a hot engine or turbos with cold water.

If it won't start after a wash: water in the spark plug wells is the usual cause. A Nissan technician told Robo this fix worked on every Z towed in for it: remove the coil packs, vacuum the water out of the plug wells, let everything dry with the hood open, refit the coils and start it.

Related pages: Injector Swap and Plenum Pull Checklist, Z32 Quick Fixes, Interior Repairs.

Sources Used