XenonZcar Banner

Z32 Common Problems and Quick Fixes

These are the small, annoying faults that most Z32 owners run into sooner or later. Each one usually takes less than an hour to fix and needs only basic tools. Most of them come from Robo's long-running Z32 tech pages (credited at the bottom), rewritten and checked against the factory manuals.

High, wandering or unstable idle

Two parts behind the throttle bodies control idle air:

  • The air regulator lets extra air past the throttle when the engine is cold, for a fast warm-up idle.
  • The idle air adjusting (IAA) unit holds the AAC valve, which the ECU uses to set the idle speed, the FICD solenoid, which raises the idle when the A/C compressor runs, and the base idle adjusting screw. See how the idle is controlled for more on these parts.

Both get gummed up with age. The proper cure is to remove and clean them, but Robo's shortcut often works and is worth trying first:

  1. Unplug the ground wires on the plenum next to the IAA to make room, and move the clutch booster vacuum hose aside (TT 5-speed). Cap or block any vacuum hose you disconnect, or the engine won't run.
  2. Remove the short hose that connects the air regulator and IAA tubes. If it's hard and brittle, replace it; ordinary 5/8″ heater hose works.
  3. With the engine running, ideally starting from cold, spray a cleaning lubricant such as WD-40 into the two open tubes: one leads to the air regulator, the other to the IAA. If the engine won't idle with them open, have a helper keep them covered between sprays.
  4. Refit the hose and the ground wires, and set the base idle (below).

Setting the base idle

The screw on the side of the IAA sets a fallback idle for when the ECU isn't controlling it. It should be set a little below normal idle, so the ECU always has control:

  1. Warm the engine up fully.
  2. Unplug the electrical connector from the IAA. If the engine stalls, the base idle is too low.
  3. Turn the adjusting screw so the engine idles on its own with the IAA unplugged, at around 650 rpm (just under 700).
  4. Plug the IAA back in. The ECU takes over and brings the idle up to its normal speed.

An unstable idle can also come from a vacuum leak, a dirty throttle body or a failing sensor. If cleaning doesn't help, read the ECU trouble codes before replacing parts.

Fuel smell in the cabin in cold weather

A gas smell that shows up when the weather turns cold, and fades once the engine warms, is almost always a loose fuel hose clamp. Rubber fuel hose hardens in the cold and seeps past a loose clamp, then softens and seals again when it warms up.

Don't ignore it. Fuel leaks under the hood have caused many Z32 engine fires. Fix it before you drive the car more than you have to.
  1. Fuel filter: tighten the clamps on both ends of the filter, and check that it's fitted the right way round (follow the flow arrow).
  2. Remove the throttle cover on the upper plenum (four 5 mm Allen screws) to reach the clamps on top of the engine: around the fuel pressure regulator, and the three around the fuel damper on the right side of the plenum.
  3. The short hose joining the front of the two fuel rails is the usual culprit and the hardest to reach. It sits above the timing belt covers, under the throttle linkage. If its clamp screws face the right way, a long, thin Phillips screwdriver reaches them. If not, try to rotate the clamps around. Replacing that hose usually means pulling the upper plenum, which is a good time to deal with the injectors too.
  4. If the fuel hoses are original, replace them. Use only fuel injection hose rated for EFI pressure. Ordinary low-pressure carburetor fuel hose can burst.

Checking these clamps once a year, before winter, is cheap insurance.

Temperature gauge drops or bounces

If the gauge dips under acceleration or jumps around, the engine is almost certainly fine. The fault is usually the gauge's sender connection. The gauge sender is on the top front of the engine, screwed into the aluminum coolant pipe just behind the fan shroud, right next to the ECU's coolant temperature sensor. Make sure you're working on the gauge sender, not the ECU sensor.

  1. Unplug the connector and wiggle the sender's spade terminal with your finger. If it moves, the rivet holding the terminal to the sender has worn loose. Engine vibration and the fan's airflow make the contact break.
  2. Tap the rivet flat with a punch until the terminal is solid.
  3. If that doesn't cure it, remove the sender and clean it with brake cleaner, and put dielectric grease in the connector.
  4. If all else fails, replace the sender. They're inexpensive.

Stock boost gauge stopped working

If the dash boost gauge stops moving but the car still pulls like it's on boost, the hose to the boost sensor has probably cracked. The sensor is a small black box on the firewall, and the hose to it runs from the intake balance tube.

  • The hose often looks fine but cracks right where it fits onto the sensor. Pull it off to check.
  • Temporary fix: trim about a quarter inch off the end and refit it.
  • Proper fix: replace the hose with 6 mm silicone vacuum hose. It takes five minutes.

If the hose is good, check the sensor's connector and wiring.

Throttle sticks after cruising

A commonly reported fault: the throttle sticks, usually after cruising in fourth or fifth gear. The cause is a small metal tube next to the throttle linkage on top of the engine. It works its way out of its fitting until it rubs on the linkage.

  • Push the tube back into place.
  • Secure it so it can't creep out again: a zip tie works, and a dab of epoxy such as JB Weld is more permanent.
  • With the engine off, check that the throttle snaps back freely from wide open, and that no cable or hose touches the linkage.
A sticking throttle is a safety problem. Don't drive the car until it's fixed.

Mystery fuses

A few Z32 fuses cause symptoms that send owners looking in the wrong place:

SymptomFuseWhere
Stereo dead, interior lights out, no door chime, alarm not working10 A “THEFT ROOM L” Under-hood fuse box, driver's side front. Not the interior fuse panel, which is why it's easy to miss.
HICAS and ABS warning lights on, power windows dead15 A HICAS Interior fuse panel in the kick panel by the clutch pedal.
HICAS, lamp and brake warning lights on10 A Eng Cont Under-hood fuse box.

If the Eng Cont fuse keeps blowing, find the short by elimination:

  1. Pull the 10 A A/C fuse (just below the Eng Cont fuse) and fit a new Eng Cont fuse.
  2. If it holds now, the short is on the A/C side. Unplug the auxiliary fan in front of the radiator, refit the A/C fuse, and see whether the fan is the cause.
  3. If Eng Cont still blows with the A/C fuse out, a likely cause is a bad lamp-out (bulb check) relay, on the back of the interior fuse panel by the clutch pedal.

A fuse that blows again straight away means a short. Find it rather than fitting a bigger fuse.

Adjusting the parking brake

The Z32's parking brake uses small drum brake shoes inside the hat of each rear rotor. There's an adjuster nut under the lever inside the car, but the factory manual says to adjust the shoes first and only then the lever. The spec is 6 to 7 notches of lever travel with a firm pull of about 196 N (44 lb).

  1. Jack up one rear wheel (or both) and remove it. Release the parking brake and put the gearbox in neutral so the hub turns.
  2. Pull the rubber plug out of the hole in the rotor hat by hand.
  3. Turn the rotor until the hole is near the six o'clock position. Shine a light in: you'll see the toothed adjuster wheel standing vertically behind it.
  4. With a flat screwdriver, turn the adjuster wheel upward (start low, push up) to spread the shoes, until it won't turn any more and the rotor is locked.
  5. Back the adjuster off 5 to 6 latches (clicks of the adjuster wheel). The rotor should then turn with no drag from the shoes. A slight scraping sound is normally the disc pads.
  6. Refit the plug and do the other side.
  7. Check the lever: 6 to 7 notches at a firm pull. If it's still out, use the adjusting nut under the lever (remove the console to reach it). The brake warning light should come on at the first notch.
  8. Refit the wheels. If you fitted new shoes or rotors, or the brake holds poorly, do the break-in procedure in the BR section of the manual.

Sources Used